Scantron Test Scanning

Tests Scantron scan bubble OMR iNSIGHT Opscan

When to Use?

Preparing to scan test or survey forms at a Scantron Scanner.
Questions? Contact Karen Burchard at 616-331-6500 or 616-485-6858 (mobile)

Obtain and use Scantron forms to administer your tests.
Note that pencil is required for filling these forms.
Bring test forms and key(s) to a Scantron location on campus.
Login at the Scantron station computer using your faculty/staff email address and password.
Follow the prompts on the Scan Menu that will appear shortly after login. The Scan Menu will step you through the scanning process.
Scantron saves scan form answers into a simple text file, and the Scan Menu will then read that file to score the test, provide options for adjusting the answer key or student answers, several reports that you can print, save, or email to yourself, and an option to save the Test Results in a csv file for uploading into Blackboard Ultra.
Be certain to log off before you leave this station.

GVSU has 7 Scantron stations , with 3 in Allendale, 3 in Grand Rapids, and 1 in Holland.
One Opscan 8 scanner is in Au Sable Hall. The other six locations have iNSIGHT 4ES scanners.

The 7 Scantron Locations are:

Allendale: 201 MAN (Manitou Hall Lab)
Allendale: 010 LIB (Mary Idema Pew Library)
Allendale: 2209 ASH (Au Sable Hall)
Grand Rapids, Health Campus: 169 CHS (Cook-DeVos Center for Health Sciences)
Grand Rapids, Pew Campus: 262C DEV (Richard M. DeVos Center)
Grand Rapids, Pew Campus: 4001 SCB (L. William Seidman Center)
Holland, Police Academy: 114 HOL (Meijer Campus in Holland)

Allendale Locations Map

Allendale campus map highlighting Manitou, Library, and Au Sable Hall

201 Manitou Hall Lab, 2nd floor Details

iNSIGHT 4ES Scanner
MAN 201
Computer Lab, Second Floor

Manitou Hall
10860 N. Campus Drive
Allendale, MI 49401

010 Mary Idema Pew Library Details

iNSIGHT 4ES Scanner
010 LIB
IT Service Desk

Mary Idema Pew Library Learning and Information Commons
10582 S Campus Drive
Allendale, MI 49401

2209 Au Sable Hall Details

Opscan 8 Scanner
2209 ASH
Room may be locked. Obtain key at Psychology Department Office (ASH)

Au Sable Hall
4045 Calder Drive
Allendale, MI 49401

Grand Rapids Locations (Map) Map

Grand Rapids Campuses map highlighting CHS, DEV, and SCB

169 Cook-DeVos Center for Health Sciences Details

iNSIGHT 4ES Scanner
169 CHS

Cook-DeVos Center for Health Sciences
301 Michigan St NE
Grand Rapids, MI 49503

262C Richard M. DeVos Center Details

iNSIGHT 4ES Scanner
262C DEV
Station is at the end of hallway, next to room 262C

Richard M. DeVos Center
401 Fulton St W
Grand Rapids, MI 49504

4001 L. William Seidman Center Details

iNSIGHT 4ES Scanner
4001 SCB
Scantron Scanner Room is directly in front of Elevator on the 4th floor.

L. William Seidman Center
50 Front Ave SE
Grand Rapids, MI 49504

Scantron paper ream purchases are handled through the Copy Center.

Reams can be ordered from the Copy Center website by clicking on “New Order” in the top menu and then selecting “Store Order”. If you have any ordering issues or need a Copy Center login, please contact the Copy Center at copycenter@gvsu.edu or call 616-331-3407.

Use Pencil only
Instruct Students to fill in their Network ID. The GNumber section may be left blank.
When using multiple answer keys, instruct Students to fill in the appropriate Test Form bubble (A, B, C, D, or E).

Note: This is the correct orientation for placing the sheets into the Scanner's input tray.
The black timing marks along the bottom edge should always be near the front of the scanner.

Use Pencil to fill forms.
Answer Key(s) should have 99999999 filled in the G-Number section (1), and correct answers marked (2) for each question to be scored. Questions left blank on Answer Key will be ignored. It is helpful (not required) to fill in the Network ID (3) of the Instructor.
Student tests must have Network ID (3) filled in to identify students. This is the same ID students use to access Blackboard, GVSU Email, and to login to lab computers.
If you have more than one Answer Key for a test , mark each key with a different Test Form (4) option: A,B,C,D,or E;
Student tests must have the appropriate Test Form option filled in to match with the corresponding Answer Key. (*help is provided during scoring if a student omits this)
Fan the sheets to help prevent them from sticking together.
Tap the sheets on the table to line them up evenly - all in the same direction.

Scan Menu Show/Hide

1. Login at the Scantron station computer using your faculty/staff login and password.
2. The Scan Menu will appear shortly after login. The Scan Menu will step you through the scanning process.

The first time you login, you may need to click the Enable Content button if you see the following:
3. Choose to scan Tests and Quizzes .
4. Use the default form: Green General Purpose Answer Sheet (GPAS) when there is only one correct answer for each question.
or choose the second form: Green GPAS read Mult Marks when you expect multiple answers on one or more questions.
Click Next >.
5. Set serial number printing options.
6. Load Test Forms: review procedures for the appropriate scanner model:

- iNSIGHT 4ES Scanner Show/Hide

Loading Scan Sheets

Inspect and Load Sheets:
1. Inspect the sheets for folds, tears, post-its, etc. Pages must be clean and flat.
  Stack scan sheets neatly – all in the same direction.
  Tap them down so they are even.
2. Press the PRESS TO LOAD button, and place sheets into the Input Tray.
  Release the PRESS TO LOAD button.
3. Be sure the sheets fall under the MAXIMUM SHEET LEVEL shown on the
  SHEET GUIDE and pull the SHEET GUIDE forward to hold sheets in place.
4. You may add more sheets after the first batch has been scanned
5. Make sure the two tabs ( READ HEAD and SHEET DEFLECTOR ) are pressed down firmly .
6. PREPARE OUTPUT BIN:
  If you have the single output tray, then adjust the
  adjustment bar to the length of the sheets you will
  be scanning.
  
  If the 2-Output Tray Select Stacker is attached to the scanner, then make sure the 2 wire handles are pulled out as far as they can go on the two output trays.
7. When the Input Tray is empty, you may load more sheets ( PRESS TO LOAD ), and then press the START button below the Display Panel to continue scanning.

- Opscan 8 Scanner (Au Sable Hall) Show/Hide

Loading Scan Sheets
1. Inspect the sheets for folds, tears, post-its, etc. Pages must be clean and flat.
  Stack scan sheets neatly – all in the same direction.
  Tap them down so they are even.
2. Place sheets into the Input Tray.
  (black timing marks along bottom edge– nearest to front of scanner)
1. Be sure the sheets fall under the MAXIMUM SHEET LEVEL shown on the
  SHEET GUIDE and pull the SHEET GUIDE forward to hold sheets in place.
2. When the Input Tray is empty, you may load more sheets into the input tray,
  and then press the START button below the Display Panel to continue scanning.
3. Test forms will pass through the scanner, have a serial number printed below
  the timing marks, and end up in the top output tray.
4. If a test form ends up in the lower output tray, this indicates a problem.
  It may be an unexpected form, or placed upside down, or it has multiple marks.
  Inspect any forms landing in the lower tray.
  If they have a serial number printed on them, then they have been scanned and recorded.
  If they do not have a serial number, you may try re-scanning them.

Scoring Test Show/Hide

7. Click Next > to begin Scanning.
ScanTools Prisma opens and displays the number of documents scanned.
8. After the last sheet is scanned, click the Stop button that appears in the lower right corner of the screen, or press ESC on the keyboard.
Scan Menu reappears to process the results.

9. You may choose to save the raw Scantron data as a simple text file (this can be used for scoring later).
Click Next.
10. Review option to correct multiple marks, and choose Yes (default) or No.
Click Next to begin scoring.
11. When multiple marks are found on a question, you will have an opportunity to make corrections.
Find the sheet and review the Question Number.
Sometimes it is obvious that one answer was intended, and you can make the correction here.

If there are many multiple marks and you do not wish to review them all, you can click
to place a check mark next to Stop Checking for Multiple Marks , then click OK.
12. When scoring is complete, you will see a score distribution chart of your test data.
The left panel provides options to generate reports, save data into a format for Blackboard, edit results and rescore.
Be certain to save or print results and log off before you leave this station.

Reports
Set the Report Header (optional)
Select All or check the boxes to select individual reports.
Then select Print, Save, or Email to obtain the reports.

Reports Include:

Response Breakdown Report
Score Distribution and Statistics
Question Discrimination Report (Item Analysis)
Multiple Marks and Corrections
Scores
Individual Student Reports

Exporting a Blackboard Compatible Scantron File

If you are planning to email your test results to your GVSU Outlook account, you must open Microsoft Outlook before scanning your test forms.

Launch Microsoft Outlook using the Windows start icon/menu.

Enter your GVSU user password.
Verify with DUO and approve.

NOTE: The above steps are only required if you intend to email the test results to yourself.

The scanning Menu will appear automatically. Select Test and Quizzes .

Scan your test forms and click Next .
Verify multiple marks and click Next .

On the Test Scoring Complete page select the Export to Blackboard tab in the menu.

On the Export to Blackboard page choose/edit the following:

Select Score Another Test or Exit Test

Note: If selecting Exit test choose either Erase and Go to main menu or Log off

Uploading the CSV File to your Blackboard Ultra Course Gradebook

Option 1: Creating a New Gradebook Item

Open the file and rename the test column to the desired Gradebook item name, this is the name that will appear in your Gradebook.

Save the file.
Navigate to your course.
Click the Gradebook tab on the top navigation menu.

In the upper right hand corner of the Gradebook , click the Upload Icon.

A new window will appear on the right titled Upload Gradebook.
Under Browse Files , click Upload Local File.

Select the file from Step 1.
Verify the information, and click Upload.

An item with the name of the score column will be created and the grades will be populated.

Located the Gradebook item, verify all the grades are correct, and click Post all grades when you want students to be able to view the scores.

You may edit the Answer Key to:

Change an Answer
Include additional correct answers (A or B, for example)
Give everyone credit for a question
Ignore a question
Mark question as Extra Credit
Change the point values for all questions or for individual questions

Choose Edit Answer Key and Points to view the Answer Key(s).
For multiple Answer Keys, use the Test Form dropdown in the upper left corner to select form A, B, C, D, or E.
Select a question number row and type the new answer or answers, or use the buttons displayed in the upper right section to change the correct answer(s), choose to give automatic credit for a question, or to ignore the question. To mark a question as Extra Credit, put a checkmark in the ExtraCredit column. Use the PointValue column to change points for individual questions. For a quicker way to set point values, choose the Change Point Values button at the top of the screen.

Changes are saved automatically.

After making changes to the Answer Key on this screen, the test will automatically be rescored.
Return to Reports , Export to Blackboard , or Export/Save Data to obtain the new results.

0 reviews

Print Article

Updating...

Scantron Test Scanning